Replacing the glass in the phone honor

Replacing the glass in the phone honor

More from Lifewire. You will have your phone repaired for very little cost. Fix Your Stuff. The home button and display flex cables are still threaded through the midframe. To reassemble your device, follow these instructions in reverse order. November 7, at pm 1 0. Badges:

Replacing the glass in the phone honor -

Lift the back cover's right edge with your suction cup, opening a slight gap between the back cover and the frame.

Insert the tip of an opening pick in the gap you created and slide it to the bottom right corner. Apply more heat if the adhesive becomes hard to cut. During the removal process, the back cover is under tension all the time and is likely to break if the adhesive isn't softened enough. Slide the opening pick along the bottom edge of the rear glass to cut the adhesive and leave it in the bottom left corner.

Slide the opening pick along the left edge of the rear glass to cut the adhesive. Slide the opening along the top edge of the rear glass and cut the remaining adhesive with it. Use a pair of tweezer to carefully peel the black foil off the loudspeaker and daughterboard cover. Remove the three Phillips 00 screws 2. Use a pair of tweezers to remove the metal shield that covers the connectors of the interconnect cable, the battery and the display flex cable.

There's a little bit of adhesive under the loudspeaker. It's possible to remove the loudspeaker without heating the adhesive but if you're having a hard time removing it, you can use an iOpener to soften the adhesive. Apply a heated iOpener to the screen to loosen the adhesive beneath. You might need to reheat and reapply the iOpener several times during the removal procedure to keep the adhesive warm enough to cut.

Once the screen is warm to the touch, apply a suction cup near the top edge of the phone right under the earpiece speaker. If the phone's screen is cracked, the suction cup may not stick. Pull up the suction cup, and insert the tip of an opening pick under the display where the earpiece speaker is located. While cutting, make sure the pick slides under the display panel and not just between the display and the front glass. Slide the opening pick from the top right corner down the edge of the phone to cut the adhesive.

Leave the opening pick at the bottom right corner of the screen to keep the adhesive from resealing. Pull up on the suction cup, and insert the tip of a second opening pick under the display where the earpiece speaker is located. Slide the tip of the opening pick to the top left corner of the phone to cut the adhesive.

Slide the opening pick from the top left corner down the edge of the phone to cut the remaining adhesive. Try not to remove the display all the way yet. The home button and display flex cables are still threaded through the midframe. Make sure the flex cable does not stick to the frame and carefully thread it through its gap. Remove any remaining adhesive from the midframe, and clean the glued areas with isopropyl alcohol and a lint-free cloth.

Keep doing this until you have removed all the glass. It is necessary to remove any adhesive still stuck on the screen. We recommend using some sort of electronic cleaning solution in order not to damage the electronic components.

Peel one side of the adhesive and stick it on the digitizer in the center. Next, use a rolling tool to make sure it is on tight. For best results, the newly assembled glass and assemblies must then be placed in an industrial autoclave to remove all left-over air pockets. Smaller vacuum devices have also been reported to give successful results. You do not need any of this equipment to repair your screen at home of your LCD and touch work ok.

You need a new glass. You can buy them for a few dollars online esp. You will have your phone repaired for very little cost. You will be able to do it without the fancy tools, and even if you end up with some dust and bubbles, you wont notice it when using the phone. Only when screen is off will you see the imperfections.

What is the optimal air pressure PSI setting for the autoclave to properly remove air bubbles? For how many minutes do I leave the refurbished assembly inside, before removing it? Add a comment BY Samsung Galaxy S6. September 23, at pm 1 0. BY kaye. September 25, at am. Step 2. Step 3. Step 4. Step 5. Step 6. Almost done! Secure the new back cover with pre-cut adhesive or double-sided adhesive tape.

To reassemble your device, follow these instructions in reverse order. You're Finished! Author with 3 other contributors. Single Step Full Guide. Small - px Medium - px Large - px. View Statistics:.

Leave the opening pick at the bottom right corner of the screen to keep the adhesive from resealing. Successfully submitted! This will keep it stable and help prevent it from breaking apart before you can get it completely off. Take your e-waste to an R2 or e-Stewards certified recycler. The amount of time it takes to heat will depend on your heater and the damage to your blass. Develop and glase products. More from Lifewire.

Replacing the glass in the phone honor -

For how many minutes do I leave the refurbished assembly inside, before removing it? Add a comment BY Samsung Galaxy S6. September 23, at pm 1 0. BY kaye. September 25, at am. BY Ahmedchapola. July 5, at pm 0 0. BY James. December 4, at am 0 0. BY curiousgeorge. June 8, at pm 0 1. BY Note 3. February 19, at pm 0 0. BY Vincent van Zyl. November 24, at am 0 0. BY Tyler Durden. February 7, at am 0 0. BY DeviceFix. November 7, at pm 1 0. You might need to spritz it a couple more times as you install the screen protector to keep it from getting too dry.

Gently place the screen protector on top of your phone's screen, starting at one end and gradually moving to the other end. Use the squeegee that came with your kit to squeeze the excess solution out from under the screen protector.

Start in the center, then gently push it out toward the edges. Hold firmly onto the protector so it doesn't move around. Leave the screen protector to dry for at least half an hour so it will fully bind to your phone's screen. Once you've got your brand-new tempered glass screen protector in place, your phone will look as good as new and you can begin using it again. Actively scan device characteristics for identification.

Use precise geolocation data. Select personalised content. Create a personalised content profile. Measure ad performance. Select basic ads. Create a personalised ads profile.

Select personalised ads. Apply market research to generate audience insights. Measure content performance. Develop and improve products. List of Partners vendors. Rose de Fremery. Rose de Fremery has been writing about technology since Facebook Twitter LinkedIn. Updated on February 27, Tweet Share Email.

Android Switching from iOS. Don't overdo it; be gentle and use a low heat setting. Introduction Use this guide to remove or replace the rear glass in the Huawei Honor Step 1 Rear Glass. Add a comment. Add Comment Cancel. Step 2. Step 3. Step 4. Step 5. Step 6. Almost done! Secure the new back cover with pre-cut adhesive or double-sided adhesive tape. To reassemble your device, follow these instructions in reverse order. You're Finished!

The you don't have a hot plate, you phone be glass to use a honor dryer, but be very careful not to overheat the assembly and damage the LCD. Attach one end of the molybdenum string to something secure. Make sure to point the sharp end of your toothpick up and away from the screen rather than down and toward it so you don't damage your screen. Add a comment. BY Samsung Galaxy S6. Slide the opening pick from the top the corner down the edge of the phone to cut the replacing adhesive.

2 Comments

  1. Kazrataxe

    Reply

    I am final, I am sorry, there is an offer to go on other way.

  2. Vocage

    Reply

    I consider, that you are not right. I suggest it to discuss.

Leave Comment

Your e-mail doesn't posted Required fields are *